HP Color LaserJet CP Series Printer The only warranties for HP products and .. Manually configure IPv4 TCP/IP parameters from the control panel. View and Download HP CPdn – Color LaserJet Laser Printer service manual online. Color LaserJet CP Series Printer. CPdn – Color LaserJet. HP Color LaserJet cyan print cartridge CEA CE . NOTE: In this manual, the abbreviation “PCA” stands for “printed circuit-board assembly.”.
|Published (Last):||21 December 2009|
|PDF File Size:||1.70 Mb|
|ePub File Size:||9.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
To specify a proxy server, enter its IPv4 address or fully-qualified domain name.
20 Most Recent HP CPDN Color LaserJet Printer Questions & Answers – Page 3 – Fixya
The DC controller sends commands to the fuser-control circuit to adjust temperatures. Figure Remove the front-top cover 1 of 2 Slide the cover toward the left side of the product to release it, and then remove the cover.
If paper is visible from the output bin, grasp the leading edge and remove it. Align the print cartridge with its slot and insert the print cartridge until it clicks into place. Table External covers, panels, and doors.
To ensure optimal print quality, HP recommends replacing a supply item when the “Replace supplies” message is displayed.
Low-voltage power supply failure Roller – Feed roller high capacity input HCI – Transmit cp3552dn paper from the cassette and feeds it to the device entrance blue. The second cam in from the right the white cam to the left of the black camshould have the second hole aligned with the hole in the sheet-metal chassis.
HP Color LaserJet CP3525 Series Printer – Control panel
Set the wake time for that day, and then choose whether the wake time should be applied to all days of the week. When it creates an image, the product scans across the page from side to side as the sheet feeds from top to bottom into the product.
The current DHCP amnual is saved.
Spring – Tension spring – Provides tension to the cartridge pressure front lever. Grasp the roller shaft collars, and lift the transfer roller off of the product.
Menu hierarchy The following top-level menus are available:. This message is displayed if a user has two or more stored jobs that require a PIN. This warranty does not apply to products that a have been refilled, refurbished, remanufactured or tampered with in any way, b experience problems resulting from misuse, improper storage, or operation outside of the published environmental specifications for the printer product or c exhibit wear from ordinary use.
Page 82 Make sure the stack fits under the tabs on the guides and does not exceed the load-level indicators. Remove the duplex-drive assembly Disconnect two connectors callout 1and then remove three screws callout 2.
Consider having a replacement cartridge available for when the print quality becomes unacceptable. If you believe you purchased a genuine HP supply, go to http: Spring – Torsion spring – Provides torsion to the cartridge lock lever. A list of available sizes appears. Locate the thumb screws on the formatter board in the rear of the product. Figure Test the primary transfer-roller disengagement sensor 2 of 2 Check the control-panel display for sensor response.
Hp color laserjet cp series printers – multiple language formatter install guide 2 pages. The range is 0 to Tools for troubleshooting The section describes the tools that can help you solve problems with your device.
Make sure that the spring callout 2 is correctly installed. Any product repair required as a result of using non-HP or unauthorized supplies is not covered under warranty. Performs additional tests to determine whether the paper path sensors are operating correctly. Cable – Rear cable assembly – Connects the DC controller board with the upper high voltage power supply.
Information about recycling used print cartridges is on the print-cartridge box. Control-panel assembly Open the front door and the right door.
If the configuration is not correct, follow the instructions on the control panel to change the size or type. AUTO resets the product to the factory default setting.
You do not have to separate the product from the feeder to remove these rollers. Pull the assembly straight out of the product to remove it.
LaserJet print cartridge limited warranty statement The control-panel assembly is attached to the product by the wire-harness connector. The lights indicate overall product status. The product has two low-voltage power-supplies for Volt or Volt input. Slide the cover toward the rear of the product and rotate it away from the product and then remove the cover.