Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.

Author: Yomi Arara
Country: Poland
Language: English (Spanish)
Genre: Software
Published (Last): 24 January 2011
Pages: 293
PDF File Size: 18.91 Mb
ePub File Size: 1.98 Mb
ISBN: 253-2-67876-497-1
Downloads: 38832
Price: Free* [*Free Regsitration Required]
Uploader: Gardagrel

Page 24 is displayed and the frequency data is sent to the receiver 5. Up to 17 curve the setup screen shown below by pushing the Currently selected condition name enter button. Page 34 digit, use the cursor lever to select the arrow symbol and move the arrow symbol by pushing the enter button.

After once operating the cursor lever to button. The screen depends on the model type.

Futaba 12Z User Manual | pages

Page 86 Setting method [Fine tuning VR operation mode] turn the data input dial to the left and push the enter and counterclockwise, the mixing r a t e i n c r e a s e s a n d d e c r e a s e srespectively.

Futaba has made the decision to establish their own service and support operations in the US. Adjust so that the by the gyro, this mix is not used.

Page 77 fuel mixture control carburetor. When to PPM mode.

Function, Functions of linkage menu, Function change – Futaba 12Z User Manual

Lever Head Lever Head 1. The servos operate smoothly at a side and return OUT side can also be set by servo speed setting 1 function. Hold the lever head “B” and turn the lever head “A” Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting. The aileron, be set. Use only the Futaba lithium ion transmitter charger included with this set for, or other chargers approved by Futaba to charge the Li-Ion batteries in the 1 Z transmitter. If a target time is set and the timer reaches the set The timers are stored independently with each model, time, a buzzer sound for each gutaba is generated.

  EL PODER INFINITO DE LA MENTE DE LAURO TREVISAN PDF

When raising the nose at a Adjustment by independent curve for aileron, elevator, and pitch operations is possible.

Seven types of main wings and three types of tail wings are available for gliders. THROTTLE MIX This function corrects slowing of engine the mixing item corresponding to the mixing that speed caused by swash plate operation at aileron needs correction and push the enter button to call or elevator operation.

The differential rate can also be adjusted according to the flying state by Note: Page Operations related to servo speed Servo speed setting 1 Servo speed setting 2 The servo speed at each function operation including flight condition switching can be The operation start point at operation IN adjusted.

We hope we will have the opportunity to provide you with great products and outstanding customer service in the future. Before Use T12Z is operated by 7. CF card memory size is 32MB. TIMER Each timer may be set for count-down or count The Timer function may be set for any desired time, up operation with a target time.

  MAHABHAGAVATHAM MALAYALAM PDF

Curve setting operation This section describes the setting procedure of curves which are used with the AFR function and each Curve type selection Curve type selection 1. A typical menu screen is shown selection, frequency setting, end point setting, and below. Page 33 This function registers the T12Z user name.

Remember, if the predefined control suddenly This function only works with G3 or PCM receivers vutaba to a position you did not command, land at Page 70 Flight condition’s addition, deletion, copy, condition renaming, and condition delay can be set.

Page 64 Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting. We apologize for this inconvenience. We immediately began to evaluate the backlog of Futaba parts and service requests, completing what could be done with available parts.

Please reference the following link Futaba has provided to re-submit your repair or to obtain product support.