Fluke A Digital Multimeter DIGIT Engineering Bench Precision OPT 02a 03 About this product. About this product. Product Identifiers. BRAND. Fluke. Full text of “FLUKE A Instruction”. See other formats. Instruction Manual P/N MARCH 1 REV 1, 3/86 ®, John Fluke Mfg. Co., Inc. All Rights. Active Filter Block Diagram A Fast A/D Converter The Fast A/ D Converter employs Fluke’s patented recirculating remainder (R2) technique.

Author: Vimuro Golkis
Country: Puerto Rico
Language: English (Spanish)
Genre: Life
Published (Last): 11 January 2018
Pages: 143
PDF File Size: 18.58 Mb
ePub File Size: 10.82 Mb
ISBN: 327-3-25354-300-6
Downloads: 84808
Price: Free* [*Free Regsitration Required]
Uploader: Mijind

Any subsequent activation of External Reference mode replaces the software number with the actual external reference value. The temporary zero correction factors are applied in dc volts V or ohms Z whenever the M2 command is in effect i.

Once a 5805a with the instrument is achieved, parts of this section will serve as a quick reference. Software calibration for each function can be accomplished locally or remotely.

The Average mode is disabled OO. Both the A and the A assume the same configuration at power up as that described for A, with the following exceptions: Data lines DB0-DB7 are used for bidirectional data flow. In Autoranging, the multimeter selects the range offering maximum resolution for the measured value.

Rent Fluke A DMM /2 Digit | Transcat

Slow filter, time-out enabled approximately ms. Error 7 External Reference error – voltage on one input exceeds 20V dc. Calibration mode entries are applied to the reading as follows; a. A check sum error 25 condition would then be set. Operation of the multimeter is straightforward.

  IFE MODAKEKE CRISIS PDF

Perform V DC Flike for interna! If dc volts, ohms, or dc amps is selected, extended resolution Flule mode is disabled, the filter is not changed, and the sample is set to S7.

Fluke A used or new for sale at used-line

This signal occurs after the measurement is complete, but before a new trigger is accepted. Nulls are discarded and not stored.

Separate modules for averaging ac or rms ac measurements are available: Power must not be cycled on or off when the Calibration mode is activated rear panel Calibration Switch on. The combination of the attenuator and feedback-controlled amplifier give gain factors 8055a 1, 10, or and attenuation factors of 8 or Front Panel Push Buttons cont A Mathematic Operations; To store the displayed value as an offset orscaling value and enter the respective mode: Interrupts are used to divert the microprocessor from the main program to service other routines.

Averaging mode is locked out: The following trigger mode transitions will occur when halt is used: Special instructions for inspection and claims are included with the shipping container.

Fluke 8505A Digital Multimeter DIGIT Engineering Bench Precision OPT 02a 03 05

Table 2A-2 details additional remote operating features available with the A and A only. Samples taken are synchronous to the line frequency for local operation. A numeric value may be entered using a store sequence. Zero mode is enabled with all temporary zero correction values set to 0.

  APGENCO AE ELECTRICAL PREVIOUS EXAM PAPERS PDF

Showing Results for Fluke 8505A

The recalled value will be displayed as long as the last push 8505q in the sequence is held depressed. If another G1 command is sent before a flukke reading is triggered, no error 00 is identified in the response.

Cleaning Instructions If Calibration mode is off, the values are stored in a temporary memory and do not affect Calibration Memory entries. Module Removal When initially commanding an ac volts function, VA2 for ac coupling or C2 for dc coupling must be used, when the multimeter isalready set for either of the other two ac volts functions, ac volts high accuracy can be selected by using S2 only.

Zero may be turned off at any time. Refer to Calibration Mode later in this section. Depending on the number of entries being cleared, several seconds may be necessary to complete this operation.

Either the normally displayed value or programmed numerics may be used for the limit values. NOTE Flashing indicators in the digit or flukee display are a warning only; they have no effect on instrument operation.

Error 2 Filter module faulty or not installed.