This instruction manual describes preventive maintenance and quick FANUC SYSTEM 3T-MODEL C is designated to be assembled inside an NC machine. Fanuc System 3T-Model D Operator’s Manual(BE 02) – Free download as PDF File .pdf) or read online for free. I am looking for an operators manual for a Fanuc 3 T controller used on a small Wasino gang lathe. Any help would be appreciated. Going to.
|Published (Last):||24 April 2018|
|PDF File Size:||2.18 Mb|
|ePub File Size:||8.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Anybody has manua, idea what that means? Tha thing look’s like a shot pin to lock the slindel to suport a barfeed or maybe index for live tooling work I have tryed to call out index on mine with no luck but the param. It was taken offline in when the company which owned it moved to a new facility and was never put back in service.
So my question probably should be.
Fanuc 3t Manuals
There are some advanced tricks to avoid re-setting G50’s for each job but start with this simple method first. Didn’t realize that featurecam defaults to using its own radius compensation in addition to the radius compensation in the fnauc offsets so the part came out a hair oversize.
Now I just need to figure out if there’s any way to set DNC on this machine First If you can post more pic’s, How Deep did you go into the mechinacal of the Lathe Bearing’s and such I have machine of the same ,anual I have maintnace 3tt and programing with paramiter list’s If I can Help at mznual mine is down with a spindel drive issue I have Igbat’s to replace and have so far replaced one the local frelance Fanuc tec told me that the top one was the most likley to be the one dead but no change in symptom’s after changing it will move on and test as I change to hopefuly find the proublem.
You must set the tools using G50’s. Results 1 to 12 of When I power the machine on, it sets zero as where-ever the table currently sits. Cold and snow now so inside work will maybe get cought up Good luck Kevin.
By roymanvega in forum Fanuc. The time now is Started out like this: Same goes for the DC ganuc. I haven’t found any hardware manual for the PL3B’s, 3y kind of an orphan product. Somewere I have littutaure on gang tooling from a local dealer for now I mounted a Quick change tool post on the slide with a riser plate ok for short run’s with few tool’s Keep up th good work You can contact me ktaylor earthlink.
Any knowledge or assistance provided in understanding this control would be greatly appreciated! We should also compare parameters and diagnostics. Results 1 to 10 of It looks like the spindle center is 2.
The first thing I manuwl when I got it home was power it on to see if the parameters were still intact. Tsugami Resto Great looking job.
I have work offsets which I can set with G10, G54, etc. From my admittedly limited understanding, I have the absolute zero which I can tweak with gridshift offsets, but does not seem to be used for anything except G28, e. Also, where the heck do you buy gang-tool style bits? This one was fun, since it came missing the plexiglass windows, I used a homebrew laser cutter to make the new ones.
I’m sure nearly any program that your old machine can handle will fit in the available memory. I have the communications working for uploading and downloading prorgams, but drip would be really nice. I’m Sorry I haven’t been helpful on a parameter list I Have a maintenance manual and I’m Still trying to find time to fix spindle drive on my machine I bought a extra PCB around the first of the year and it got here damaged maunal It will make a core at least I Have a complete servo drive new in the box for the XorZ of this machine.
Mostly I took everything that I could unbolt apart and sandblasted it, did have to fix the turcite on one of the ways.
Fanuc > FANUC 3T PARAMETERS
I’m wishing Fanuc had more info on these older units. Let me know if there’s anything I can do to help you with your unit!
Imagination will take you everywhere. Need help understanding “zero” on a Fanuc 3T. So if the table moves 1″, the majual said 2″. Let me know if I can help with what documation I have.
The parameter descriptions are in the back of a Fanuc System 3T operator manual.
It also lets you see the program as its running through it. You will need it several times. I tore into it pretty good, but I didn’t take apart the main spindle bearings since it spun cleanly up to RPM.
Last edited by Kevin Taylor; at Did you do fanud number on the DC servo’s? Fanuc paramater’s Yaddatrance are you in the US Location? Program input is started with the data input external start signal MINP. Helwig Carbon are a source of brushes, BTW. Thank god for Duracell Professional Ad text and spelling. Look’s like you have a Hydro unit I don’t have for the manusl bar. But all of the information I can find seems to imply that its only used after major operations like replacing the servo manuap ballscrew and where you need to realign turrets and such.
I’m very familiar with machining centers, but I’m in need of some assistance translating that into “ancient” CNC lathe operation. I worked a 3T many years ago. Specifically, how the displayed ‘zero’ is related to the machine reference coordinates.