Modular Fixture Design for BIW Lines Using Process Simulate® .. Tapping, Testing, Turning, Welding, Robotic Spot Welding, Robotic Painting. BIW WELDING FIXTURE UNIT BIW welding fixtures are used for holding the sheet metal or part assembly together in space while the components are. BIW Fixture Design solution: HRT provides service solutions with top quality for BIW Welding Fixtures in Automotive Industry. We provide complete BIW Fixture.
|Published (Last):||3 February 2004|
|PDF File Size:||15.85 Mb|
|ePub File Size:||5.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Location layout is the selection of the positions and numbers of locators and clamps for assembly of fixture components into a final configuration on a fixture base.
BIW Welding Fixture Manufacturer, Sheet Metal Dies Manufacturer – Tata Motors PED
The surface of base should be flat smooth and the base should be rigid enough for easy welding and machining. The dimension from the panel to the locating pin leading end straight area should be 5 mm.
In other words a clamp is a force-actuating mechanism of a fixture unit. Help Center Find new research papers in: There are two configurations for position of locating pin: The generalized requirements of clamping device can be summarized as: The body part is constrained by a set of appropriately locating pin so total constraint by locating pin should be fully constrained at all times to prevent any movement. It involves numbers of fixture units and due to the complexity and shape of the component geometry, the choice of elements as well as configuration of each unit tends to change from case to case.
The taper lead angle is large, 60 degrees or less, for small-size body parts and manual operation, but it is frequently between10 and 30 degrees for large-size body parts that are difficult to handle. The framework of the base is usually made of shape steel.
BIW Welding Fixture Design
flxtures Load condition and configuration are not uniform, so it is impossible to set a base shape in general. Clamping device In every welding operation for body assembly, clamping of panel is an essential requirement. Locating pins are available in numerous shapes and sizes in a design.
Fixture unit to hold the body parts securely and composed of following item: There is deformation of body assembly due to the welding process effect and resulting variation due to part dimensional variation, when you are designing a fixture you should eliminate them and another objective is achieving fixtrues quality within the required tolerances, so you can achieve this purpose by planning location layout.
Log In Sign Up. Usually two locating pins are enough to properly locate the body part on one plane.
One of the pins is round, and another one is diamond shaped. So, designing a fixture in this plane bia often a complex process, considering the variations in coordinate systems and basic rules such as maintaining few elements in specific orientations.
A clamp can be defined as a device for providing an invariant location with respect to an external loading system.
The end of each pin has a round or conical shape or is chamfered for the purpose of maintaining workability such as ease of loading and quality such as prevention of aelding. This configuration will allow easier loading of body part. Skip to main content. The difference between the locate hole in the panel or body part and the locating pin diameter should be 0.
The forces exerted by the clamps hold a panel securely in the fixture against all other external forces. Designing a welding fixture is based on the location layout.
Click here niw sign up. In most applications, locating surface devices locate a panel by its external flat surfaces and flat area, such as: The shape of locating surface is a form of cross-section of panel. When a welding process is producing a load or moment on the body part, it is necessary that a sufficient clamping force must be exerted to withstand such actions.
Enter the email address you signed up with and we’ll email you a reset link. This is usually done with the datum surfaces that are reference for locating surface.
Sheet Metal Fixtures
Remember me on this computer. Locating surface is configured to receive panel for setting in a correct position and locating a body part from any surface such as flat, curved, or have fxtures irregular contour. The dimensions of datum surface are decided by selecting a necessary cross- section from the part drawing.