The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Akisho Voodookasa
Country: Cameroon
Language: English (Spanish)
Genre: Politics
Published (Last): 28 December 2004
Pages: 55
PDF File Size: 4.34 Mb
ePub File Size: 15.69 Mb
ISBN: 634-5-22519-236-8
Downloads: 45261
Price: Free* [*Free Regsitration Required]
Uploader: Makinos

Ground yourself and use an ESD mat.

If you have ever managed wtmega328 program the fuses, the reset pin may have been disabled, or the device may be expecting an external crystal. Have you applied power to the circuit? Atmega 2 9 If this question can be reworded to fit the rules in the help centerplease edit the question.

It looks like the log text says ‘programmer operation not supported’, tqp be a symptom of bad cmd line args. Error while burning bootloader. That is pretty much all you need. The AVR programmer will not supply power. This question does not appear to be about electronics design within the scope defined in the help center.

Check that the ISP header connects to the pins that it ought to, and check that you have the chip oriented correctly in the socket The USBtiny has a switch to power the target, so make sure that’s in the correct position. Only HV programming does not.

  EDWARD PENNEY ECUACIONES DIFERENCIALES PDF

Buy Products Online from China Wholesalers at

Home Questions Tags Users Unanswered. ISP requires a working clock source. ATmegaP Chip Erase delay: SCK serial program mode: Crystal requirement comes when booting through the bootloader i.

Assuming your connection is incorrect, first you need to add a pull-up resistor to the reset pin; 1kk should be alright.

ATmega328P Microcontroller – TQFP

Tqqfp I’m doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it. Can you edit the question to include the exact command-line arguments given to avrdude?

I’m voting to close this question as off-topic because it has been abandoned for half a year in unanswerable state. If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to recover it. If all that is correct, there are a couple other things that could cause that error: Well first of all, check the wiring.

Using SCK period of 10 usec avrdude: Atmeg3a28 programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external clock.

  KANTECH KT-200 PDF

However, when attempting to upload the bootloader to the chip, I am presented with the following error:. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

It’s worth checking its in the correct position, though. If all that is correct, there are fqfp couple other things that could cause that error:.

Reset is driven by the programmer, and besides has an internal pullup. I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip on right. Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes 0xff 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 no 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type: Any amtega328 would be appreciated.

The reset pin lacks the normal ESD protection, and so is fairly easy to fry. TomCarpenter, the programmer does provide power.