¼” screws at four jamb corners – screws bending corners screws bending. – tearing in frame wall at connections pushing limits of ASTM F □ Minimal. ASTM F Standard Practice for Specifying an Equivalent 3-Second Duration Design Loading for Blast Resistant Glazing Fabricated with. Mullion/Frame Design – Allowable Stress Design. ▫ Design Load = Equivalent 3 second design load ASTM F ▫ Info Required –. ▫ 1) Level of Protection.

Author: Gozuru Moogutaxe
Country: Kosovo
Language: English (Spanish)
Genre: Life
Published (Last): 13 June 2013
Pages: 43
PDF File Size: 17.4 Mb
ePub File Size: 8.4 Mb
ISBN: 427-5-74879-251-4
Downloads: 31851
Price: Free* [*Free Regsitration Required]
Uploader: Kigalar

Use of the annealed or heat strengthened glass plies asmt also reduce the amount of load transferred into the structure. Values given in parentheses are for information only.

Blast testing has shown that use of fully tempered glass plies, when fractured during a blast event, have poorer post blast performance than annealled or heat strengthened glass plies. Blast testing has shown that use of fully tempered glass plies, when fractured during a blast event, have poorer post blast performance than annealled or heat strengthened glass plies.

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least: ASTM F is a standard practice for specifying an equivalent 3-Second Duration design loading for blast resistant glazing fabricated with laminated glass.

ASTM F 2248

ASTM International which was funded inis aatm international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services.

Values given in parentheses are for information only. The system shall be designed to ensure that the glazing fails prior to the framing system that supports the glazing and its attachment to the structural framing system.

The width of silicone or glazing tape is referred to as bite and is shown and discussed in Guide C From Wikipedia, the astk encyclopedia.

  ASRAR E KHUDI IN URDU PDF

ASTM F2248 – 12

This page was last edited on 28 Marchat As a minimum, insulating glass shall use laminated glass for the inboard protected side lite. The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least: The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration The main keywords to present this standard are air blast pressure, blast resistant glazing, explosion, insulating glass, and laminated glass.

The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration. Link to Active This link will always route to the current Active version of the standard.

ASTM F – Wikipedia

It is the responsibility of the user of this standard to establish appropriate safety and health practices ast, determine the applicability of regulatory limitations prior to use. Historical Version s – view previous versions of standard.

Link to Active This link will always route to the current Active version of the standard. This standard was published by ASTM F14 which is a committee specializes about on systems products and services. Work Item s – proposed revisions of this standard.

Glass plies used to construct laminated glass are recommended to be either annealed or heat strengthened glass. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist ast, uniform load acting on the blast resistant glazing that has a magnitude of at least:.

  CATALYST 2960S 24 GIGE 4 X SFP LAN BASE PDF

The width of glazing tape shall be at least equal to two times but not more than four times the thickness designation of the glass to which it adheres. The width of glazing tape shall be at asmt equal to two times but not more than four times the thickness designation of the glass to which it adheres.

xstm

The main keywords to present this standard are air blast pressure, blast resistant glazing, explosion, insulating glass, and laminated glass.

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least:. As a minimum, insulating glass shall use laminated glass for the inboard protected side lite. Views Read Edit View history.

The system shall be designed to ensure that the glazing fails prior to the framing system that supports the glazing and its attachment to the structural framing system. Retrieved from ” https: Laminated glass fabricated with fully tempered glass plies has a tendency to leave the supporting glazing system frame after fracture whereas laminated glass fabricated with annealed or heat strengthened glass plies will remain in the frame and absorb remaining load through tensile membrane behavior.

Laminated glass fabricated with fully tempered glass plies has a tendency to leave the supporting glazing system frame after fracture whereas laminated glass fabricated with annealed or heat strengthened glass plies will remain in the frame and absorb remaining load through tensile membrane behavior.

Active view current version of standard.