This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Rubber. ASTM D is an abrasion method used for coated materials and is cited for classification testing by the ANSI standard. ASTM D Abrasion resistance tests are intended to measure the wear resistance properties of a material. This may be correlated to expected end use.
|Published (Last):||5 January 2012|
|PDF File Size:||17.65 Mb|
|ePub File Size:||4.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Abrasion – Argen Polymer LLC
Collectively, these considerations will facilitate your selection of the most appropriate fabric for the project. There is no correlation between Wyzenbeek and Martindale results.
Mechanical property of film — Section 9: This standard does not specify aesthetic and dimensional requirements. EN Resilient Floor Coverings-Tiles of agglomerated composition cork with polyvinyl chloride wear layer-Specification This European standard specifies the characteristics of agglomerated cork with a wear layer based upon polyvinyl chloride and modification thereof.
A Wyzenbeek machine is used for this test allowing samples of the test fabric to be pulled tight in a frame and held stationary. Wyzenbeek results abovedouble rubs have not been shown to be an indicator of increased lifespan.
This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure.
This specification covers adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external equipment identification or instruction see 6. Wyzenbeek testing measures flat abrasion resistance and does not consider edge abrasion or other types of surface wear that may occur in actual upholstered applications.
Providing solutions to help our customers make Better Measurements. It is intended as a means of characterizing coatings used on surgical implants. Description of a method that measures the ability of a coated surface to resist abrasive wear-through to the underlying substrate by assessing the resistance to liquid paraffin fat in the abraded area.
The number of cycles that the fabric can endure before fabric shows objectionable change in appearance yarn breaks, pilling, holes is counted. Sstm purpose of this test is to provide a general means to produce controlled abrasion on a card surface. This guidance document represents the agency’s current thinking on the testing results that will enable FDA to reconsider the requirement for postmarket surveillance of plasma sprayed hip prostheses.
The values given in parentheses are for information only. Historical Version s – view previous versions of standard. SAE J Method of Testing Resistance to Scuffing of Trim Materials This test can be used to determine the resistance to scuffing of test specimens such as fiberboards, fabrics, vinyl coated fabrics, leathers, and similar trim materials.
Wire screen or wire mesh is used as an abradant when the test specimen is more abrasive than the cotton duck. ASTM D Standard Guide for Testing Industrial Water-Reducible Coatings This guide covers the selection and use of procedures for testing water-reducible coatings, both pigmented and clear, utilizing synthetic lattices, synthetic resin emulsions, or water-reducible alkyds. This Standard sets out a method for determining the abrasion resistance of a paint coating or other finishes, such as anodizing, electroplating, paper products, rubbers, plastics, textiles, glass and concrete.
Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)
This European Standard specifies the functional requirements and test methods for wash basins for domestic purposes. This standard sets out a method for the determination of the abrasion resistance of textile fabrics applicable to all textile fabrics including coated and laminated fabrics, a method for wet testing is also specified.
While abrasion resistance often stated in terms of the number of abrasion cycles and durability are frequently related, the relationship varies with different end uses and different factors may be necessary in any calculation of predicted durability from specific abrasion data.
NASTA Manufacturing Standards and Specifications for Textbooks If offset printed on coated cover material, a protective top coating for abrasion resistance is required. This explains the requirements for both residential and contract spaces. This process standard specifies procedures and requirements for hard anodizing aluminum alloys.
GG-Pb Plates and Foils, Photographic Photosensitive Anodized Aluminum This specification covers the requirements for photosensitive anodized aluminum sheets and foils. ACT reminds you that there are many points to consider when specifying textiles. This specification covers requirements for electrolytically formed oxide coatings on magnesium and magnesium alloy parts where appearance, abrasion resistance, and protection against corrosion are important. This test method describes a procedure for determining the amount of image abraded from the surface of a document.
This test method covers the laboratory procedure for determining the abrasion resistance of resilient flooring using an abrader with a grit feeder. A fabric with twice the number of abrasion cycles does not indicate double the service life. SIS 92 35 09 Floor Materials – Determination of Abrasion Resistance This standard describes a method for the determination of the abrasion resistance of organic flooring materials when exposed to walking traffic of a revolving nature point abrasion.
Association of Contact Textiles Website. Two test methods are included. This standard specifies a method for determining the resistance to surface abrasion of decorative surfaces by using the Taber abrader.
Understanding Abrasion Testing – Alendel Fabrics Ltd.
This may be correlated to expected end use performance. Test Method A uses a device that contains an abrasive wheel.
This European standard specifies the characteristics of agglomerated cork with a wear layer based upon polyvinyl chloride and modification thereof. This document details the NMP best practice for the acceptance and verification of coatings and paint finishes applied to Nokia plastics for the Menu system. This specification covers three types, four classes, and two forms of laminated or coated cloth.
This International Standard specifies requirements for hard anodic oxidation coatings on aluminum and its alloys, including test methods. All of the following issues should be included in any such assessment: United Nations – ECE Regulation 43 Uniform Provisions Concerning the Approval of Safety Glazing Materials and their installation on Vehicles This Regulation applies to safety glazing and glazing materials intended for installation as windscreens or other panes, or as partitioning, on power-driven vehicles and their trailers.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
The test measures the ability of the decorative surface of the sheet under test to resist abrasive wear-through to the sub-layer. This guide provides a common basis on which protective coatings for the surfaces of light water-moderated nuclear power generating facilities may be qualified and selected by reproducible evaluation tests. ISO Road Vehicles – Safety Glazing Materials – Mechanical Tests This International Standard specifies mechanical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.
EN Resilient floor coverings – Determination of wear resistance – Part 2: