ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.

Author: Samushakar Zutaxe
Country: Belarus
Language: English (Spanish)
Genre: Technology
Published (Last): 4 October 2010
Pages: 26
PDF File Size: 2.45 Mb
ePub File Size: 1.79 Mb
ISBN: 277-5-55336-653-9
Downloads: 42082
Price: Free* [*Free Regsitration Required]
Uploader: Faetilar

MPa Permission rights to photocopy the standard may also be secured from the ASTM website www.

Surface Requirement Bend Tests S1. Each pair of these bends will place opposite surfaces of the sheet or plate material in tension. When the straight edge is placed on a single high point, the maximum deviation from the plate at each end shall be no greater than 0.

ASTM B _图文_百度文库

Samples shall be taken from the ingot or the extremes of the product to be analyzed. C Single values are maximum. Approved April 15, For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown.

Approved May 1, sstm The grades of titanium and titanium alloy metal covered by this specification shall have the chemical composition requirements of: ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Alternate Yield Strength Maximum S2.

The bend specimen may be of less than full material thickness; however, the outer surface of the specimen must include the original material surface with no material removal or surface conditioning other than at the rounded corners, and must otherwise be representative of the product as supplied.

  LIBRIS MORTIS THE BOOK OF UNDEAD PDF

B — 10 Standard Specication for Titanium and Titanium Alloy Strip, Sheet, and Plate1 This standard is issued under the xed designation B; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

Product analysis limits shall be as specied in Table 3. This standard has been approved for use by agencies of the Department of Defense. A number in parentheses indicates the year of last reapproval. Two bends shall be made in the L direction and two in the T direction. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Thickness is measured along the longitudinal edges of the plate at least 38 in. Bend tests are not applicable to material over 0.

NOTE 2—If the longer dimension is under 36 in. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

Users of this standard are expressly advised that determination of the astmm of any such patent rights, and the risk of infringement of such rights, are ast their own responsibility. B Bend to Radius of Mandrel, T equals the thickness of the bend test specimen.

Titanium Plates, Sheets & Coils

Other elements may be present in titanium or titanium alloys in small quantities and are inherent to the manufacturing process. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  INVESTIGACION DE OPERACIONES TAHA 5 EDICION PDF

The test report shall, at minimum, indicate acceptable or unacceptable results. Committee B10 has identied the location of selected changes to this standard since the last issue B – 08b that may impact the use of this standard. For plates up to 10 in.

Specimens shall be taken bb265 sheet or plate material produced from the same ingot or bloom materials, processed the b625 way to the same nominal thickness, width and length, produced in one production run or campaign, nished in the same way, and otherwise representative of the material supplied. In titanium these elements typically include aluminum, vanadium, tin, chromium, molybdenum, niobium, zirconium, hafnium, bismuth, ruthenium, palladium, yttrium, copper, silicon, cobalt, tantalum, nickel, boron, manganese, and tungsten.

B For thicknesses under 0. Permissible Variations in Dimensions 7. This specification covers annealed titanium and titanium alloy strip, sheet, and plate.

Other elements may not be added intentionally. Current edition approved May 1, Committee B10 has identied the location of selected changes to this standard since the last issue B – 09 that may impact the use of this standard.

This is in accordance with the round-off method of Practice E The bend shall be made on a radius equal to that shown in Table 1 for the applicable grade. Alternate techniques are discussed in Guide E Therefore, properties for aged material shall be negotiated between manufacturer and purchaser. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.