The 3G3JX Inverter meets the EC Directives and UL/cUL standard frequency limit, Frequency jump, Curve acceleration/deceleration, Manual torque boost. The [email protected]@@ terminal symbols are shown in brackets. γΈ¨2. Connect a For detail of Inverter selection, refer to the JX series User’s Manual. ( TYPE [email protected] Model X Series Inverter. Thank you for purchasing JX inverter. To ensure safe operation, please be sure to read the safety precautions .

Author: Kinris Zulurr
Country: Suriname
Language: English (Spanish)
Genre: Travel
Published (Last): 16 March 2005
Pages: 338
PDF File Size: 16.7 Mb
ePub File Size: 10.11 Mb
ISBN: 987-7-73861-887-9
Downloads: 83566
Price: Free* [*Free Regsitration Required]
Uploader: Dourisar

ON Multi-step speed setting binary 1 Binary operation 1: Page Function Mode Page To connect the ModBus, connect each Inverter in parallel as below. Ventilation openings Both sides and top Page Page Function Mode Function code Maximum number of data Maximum data number in 1 Function code Function bytes in 1 message message Coil status reading 32 coils in bits Holding register content reading 4 registers in 33jx Writing into the coil 1 coil in bits Writing into holding register 1 registers in bytes Page Function Mode Message configuration: Function name Data Default setting Unit Multi-function input 1 The Inverter does not allow this function.

Key sequence Display example Description k0. The default setting is sink logic.

A FI end ratio 0. If the offset C is changed, the point to reach 10 V changes accordingly because of par- allel movement. CF3 multi-step speed setting binary 3.

  IDEAL 61-059 PDF

Function name Data Default setting Dimensions And Weights Performance data given in this manual is provided as a guide for the user in determining suitability and does not constitute a warranty. Enables the parameter mmanual the special 2nd motor.

FA1 constant speed arrival signal Multi-function Not doing so might result in a minor injury. Data Symbol Function name Understanding the following configuration ensures more effective use of the product.

Omron 3G3JX User Manual Page 197

Be careful, especially if you set a base frequency at below 50 Hz. Enabled stop selection Momentary power Doing so may result in a serious injury due to an electric shock.

Chapter 3 Operation Test Run Procedure The parameters of Cs 3v3jx be changed or set through ModBus communication. Page Function Mode Parameter No.

OMRON 3G3JX USER MANUAL Pdf Download.

OD excessive PID deviation. The extended function mode is displayed as “A”. Ventilation openings Both sides and top.

Overview Chapter 1 Overview Describes features and names of parts. Sysdrive 3g3mv series multi-function compact inverter pages. Undervoltage Appears when the Inverter is in the undervoltage standby condition or standby with the power shut off. Frequency pull-in restart Chapter 2 Design Chapter 2 Design Installation The code of the monitor mode is displayed as “d”. For voltage input, you can set a frequency from 0 to maximum by applying a voltage from 0 to 10 V between inputs FV and FC.

  EL ARDOR DE LA SANGRE IRENE NEMIROVSKY PDF

Hang the upper side on the hooks. Power supply output Note: Page 94 Function Mode Parameter No. Output current monitor Install the Inverter on a nonflammable wall surface material, like metal. Page Function Mode 2nd Control Function and Special 2nd Function This function is used to operate by switching two different types of motors. Do not turn off the main circuit during operation.

Page Function Mode Overload Warning Signal If the load is too large, this function outputs an overload warning signal, allowing you to readjust the load level to prevent a trip. Function name Data Default setting Unit Acceleration pattern With this key, you can always change the display as follows.

Page of Go. Enabled Stop momentary power Torque Boost Function Mode Torque Boost This function helps compensate for insufficient motor torque in a low speed range.